Product Description

[N Gauge Kit Auto crossing]
- I realize a printed circuit board with the most demand in the traditional kit, automatic control mosquitoes.
In addition, the redesigned assembly instructions easy to understand even more.
Can be fabricated more easily. Automatic control system for model railways from the fact that there are a variety of ways
Vehicle sensor takes care like you can select the customer.
Therefore the sensor is not affiliated.

- Flashing LED with this kit, you can be done by automatic control model according to the passage of the vehicle crossing the sound.
TCS sensor can respond to and TOMIX made (such as reed switch) contact input sensor system with this kit.
Further by connecting the sensor unit (sold separately) CDS sensor vehicle, rail current sensing circuit (track)
It is also possible to adapt to.

※ This kit does not include a vehicle sensor.
Please prepare yourself to fit the model you have.

[Specifications]
- Supply voltage: DC9 ~ 12V
- Operating current: 3mA ~ 5mA (only a single IC, except speakers)
- Output: LED output with two chord

Operation of this kit]
- On the line, installed in order SENSOR1, crossing the body, of SENSOR2.
- I will stop working when the train passes through the SENSOR1, and then passes through the SENSOR2.
- Accepts the following train train passes through two completely SENSOR, 5 seconds after.
- So also works in the direction passing through the exit to the SENSOR1 SENSOR2, \u200b\u200bwe also support a single line.
- After passing through the SENSOR1, direction of travel is reversed in the middle of the train does not pass through the SENSOR2,
When you pass through the SENSOR1 again, we will not stop the operation of the crossing.
※ Please note that we can not support the operation you want to change direction in the middle of the crossing, such as replacement.
- Preceding train the following train in the same direction passes through the (2) SENSOR1 within 5 seconds after passing through (1) SENSOR2
Will not work because it is recognized as the same train.

[Content of set]
- (1) Speaker: one
- Dedicated printed circuit board (2): one
- (3) IC: Each 1 MK-N02-P1 ×
- (Sound crossing) (4) IC: Each 1 MK-S02-MPRB ×
- (5) IC socket pcs: 2 8Pin ×
- (Red) 1005 Size (6) Chip LED: four
- (Red) 1608 Size (7) Chip LED: four
Line - (8) enamel: 1.2m
- Oscillator (9) Ceramic pcs: 1 20MHz ×
- Built-in resistors (10) pcs: 1 DTC114ESA ×
- Terminal regulator (11) 3 pcs: 1 78L05 ×
- (12) ceramic capacitor pcs: 2 1μF ×
- Electrolytic capacitors (13) × 1 22 ~ 47μF ×
Resistance - (14) × 2 1KΩ ×, each 10KΩ × 3
- Cable for (15): 1m × 2
- Battery snap (16): 1
- Automatic crossing N gauge kit assembly instructions

※ vehicle sensor part and model of crossing is not included.
※ battery, cases are not included.

[Connection with sensor]
- This kit is used to connect the two sensors and SENSOR2 SENSOR1.
- Place of crossing back and forth across the SENSOR2 and SENSOR1.
Operation, refer to the Behavior of the kit.
- Please install and adjust the timing and location of each crossing SENSOR.

- This kit can be connected (such as a reed switch) contact input.
In addition, CDS light sensor or by using the optional [sensor unit vehicle]
That corresponds to the current sensing circuit that I can track.

- If the reed switch:
Reed switch should be connected to the terminals of the SENSOR1, 2 of the kit.
I sensed that you installed in line with the reed switch, attach a magnet to the vehicle. (See figure at right)
Adjust the direction and distance of the reed switch and magnet mounting.
- For companies TCS sensor TOMIX:
I rose earlier to remove the connector from the sensor cable of TCS. (See figure at right)
SENSOR1 of the kit, connect the cable that corresponds to the figure on the right to each terminal of the few.
In addition, the sensor which does not correspond to a different sense of direction in TCS sensor kit
It is also good orientation.
- If the sensor unit MES company vehicle (optional):
OUT1 ~ 4 respectively to each terminal of the vehicle of the sensor unit 4 SENSOR1 ~ this kit
Connect.
Please refer to the manual of the sensor unit for each vehicle with the sensor connection.

[Track]
- # (Electronic sound of the type that is used in some of the private railway) crossing sound MPRB

[Notices]
- Because I can make a printed circuit board only, without having read a circuit diagram! ( more information )
Okay - even for beginners! Illustrated with manual soldering! ( more information )

[Related Products]
- Pre-wired chip LED set:
[Sounds difficult ... wiring] At that time, the
Please use the [chip LED pre-wired set.
In advance, it is the chip LED of the state that has been soldered enameled wire.
- Regulator Kit:
If you want to ask for a voltage greater than the power of our specification of the kit,
Please use the kit here.
- AC adapter set:
If you want to ask for a kit at our (100V) household electrical outlet,
Please use the set here.
Unit - double track:
With the purchase of the kit together here, If you are planning on is a great-value double track.



Item Size/Weight : 20 x 14.7 x 3 cm / 116g

Product Specifications

Item series

Control Systems

Item code

MK-S10N-MPRB

JAN code

4582405280042

Purchase Information